裂缝性孔隙介质频变AVAZ反演方法研究进展

由于尺度的限制,利用地震方法进行裂缝参数定量表征一直是地球科学的难题。基于裂缝性孔隙介质动态等效理论的频变AVAZ反演方法给出了研究思路。首先介绍了裂缝性孔隙介质的等效介质理论研究进展,分析比较了各种裂缝性储层岩石静态等效介质模型和动态等效介质模型;然后给出了基于Chapman模型的裂缝参数和渗透率定量表征的正问题数学模型以及反演问题求解的方法和策略,以及基于模型数据的数值计算结果;最后讨论了频变AVAZ反演方法目前存在的问题和进一步研究方向。     

NSGA-Ⅱ和NSGA-Ⅲ应用于换热网络多目标优化的对比

针对换热网络多目标优化问题，采用目前应用较广泛的两种多目标遗传算法，即NSGA-Ⅱ和NSGA-Ⅲ，对两种算法的性能进行对比研究。案例研究结果表明，NSGA-Ⅱ算法比NSGA-Ⅲ算法运行效率更高，NSGA-Ⅲ的运行时间是NSGA-Ⅱ的2倍以上；NSGA-Ⅱ算法的应用并不严格地受限于3个目标的最大目标数量，NSGA-Ⅱ在求解大于3个目标的多目标优化问题时也可能具有良好的性能，目标数量并非选择NSGA-Ⅱ和NSGA-Ⅲ算法的严格标准。对10×5换热网络案例进行4个相关目标改造优化时，从换热网络的单一性能指标来看，NSGA-Ⅱ算法更容易获得各目标的极值。从最小年度总费用的评价指标来看，两种算法的最优方案效果相近。对7×3换热网络案例进行6个目标的优化时，NSGA-Ⅲ算法得到各目标的极值较优。从最小年度总费用的评价指标来看，NSGA-Ⅲ算法获得的投资费用和年度总费用更小。对于目标函数数量不超过3个，或者3个以上具有一定相关性的多目标优化问题，推荐优先使用NSGA-Ⅱ算法实现快速寻优；而NSGA-Ⅲ算法由于其基于参考点的选择机制，运行效率较慢，更适合用于收敛困难的高维多目标优化问题。     

Densification mechanism during reactive hot pressing of B4C-ZrO2 mixtures

The densification behaviors of pure B₄C and B₄C-ZrO₂ mixtures were compared during hot pressing. The results showed that in-situ formed ZrB₂ effectively enhanced the densification process of B₄C-ZrO₂ mixtures, more significantly during the intermediate stage. Within the relative density ranging from 0.75 to 0.90, the B₄C-15?wt%ZrO₂ mixture (B15Z) achieved the maximum densification rate as twice much as that of pure B₄C. The stress exponent n>3 indicated plastic deformation was the dominant densification mechanism of B15Z. The viscosities of plastic flow were evaluated using Murray-Rodger-William equation and the viscosity of B15Z was only a quarter of that in pure B₄C. The sintering activation energy was calculated to be 305.9?kJ/mol for pure B₄C and 197?kJ/mol for B15Z, respectively. It was proposed that the lower viscosity of plastic flow and activation energy accelerated the sliding and propagating motions of plastic flow, by which underlain the enhanced densification behaviors of B₄C-ZrO₂ mixtures.     

萍钢高炉大修放残铁工艺实践

对萍乡萍钢炼铁厂2号、3号高炉大修放残铁的过程进行分析,总结放残铁的工艺控制心得,为今后高炉安全、顺畅、干净放残铁提供借鉴。     

基于个体协同触发强化学习的多机器人行为决策方法* .txt

摘要：为了提高多机器人行为最优决策控制中强化学习的效率和收敛速度，研究了多机器人的分布式马尔科夫建模与控制策略。根据机器人有限感知能力设计了个体 协同感知触发函数，机器人个体从环境观测结果计算个体 协同触发响应概率，定义一次触发过程后开始计算联合策略，减少机器人间通讯量和计算资源。引入双学习率改进Q学习算法，并将该算法应用于机器人行为决策。仿真实验结果表明，当机器人群组数量在20左右时，本文算法的协同效率较高，单位时步比为1085 0。同时距离调节参数η对机器人协同搜索效率有影响，当η=0008时，所需的移动时步比和平均移动距离都能达到最小值。通过双学习率的引入，该算法较基于环境模型的强化学习算法具有更高的学习效率和适用性，平均性能提升35%，对于提高多机器人自主协同能力具有较高的理论意义及应用价值。 .txt     

Microwave dielectric properties of SrLa[Ga1−x(Mg0.5Ti0.5)x]O4 and SrLa[Ga1−x(Zn0.5Ti0.5)x]O4 (x = 0.2-0.8) ceramics

SrLa[Ga_1−x(R_0.5Ti_0.5)_x]O₄ (R = Mg, Zn) ceramics were prepared by a standard solid state sintering method. The single-phase ceramics with K₂NiF₄-type layered perovskite structure and I4/mmm space group were obtained, indicating that SrLa(R_0.5Ti_0.5) and SrLaGaO₄ can form the unlimited solid solutions. With increasing x for R = Mg and Zn, ε_r increases monotonously, the Qf value first increases and then decreases, while τ_f increases from a negative to a positive value. The optimized microwave dielectric properties were obtained as following: ε_r = 23.3, Qf = 89 400 GHz, τ_f = −0.8 ppm/°C for SrLa[Ga_0.6(Mg_0.5Ti_0.5)_0.4]O₄ and ε_r = 23.3, Qf = 76 200 GHz, τ_f = 0.2 ppm/°C for SrLa[Ga_0.7(Zn_0.5Ti_0.5)_0.3]O₄, indicating that the present solid solution ceramics are the promising candidates as microwave resonator materials for the telecommunication applications.     

湖北省保康县荆山玉地球化学特征及其成因分析

荆山玉是湖北省保康县新发现的一个玉石品种,形成于大陆边缘—洋盆区过渡带的热水沉积环境,为晚震旦世—早寒武世灯影组的一种硅质角砾岩:原地震碎角砾岩,由角砾和胶结物二部分构成,角砾局部可拼接;角砾成分为早期硅质岩碎裂产物,胶结物除早期硅质岩碎裂产物外,还有少量后期充填的石英、铁质等,受角砾、胶结物颗粒大小、裂隙发育程度不同的影响,后期热液改造程度不同,角砾和胶结物化学成分存在一定的差异,色调与铁质有关。荆山玉的形成主要经历了三个阶段的演化:第一阶段,低温150～225℃、弱氧化—弱还原条件下热水成因的硅质岩形成;第二阶段,热力膨胀外力作用下,硅质岩局部原地震碎形成硅质角砾岩,热水温度243～340℃,富氧氧化—贫氧过渡环境,红褐色的Fe~(3+)在胶结物、裂隙中富集;第三阶段,热水温度116～127℃、缺氧还原条件,黄色的Fe~(2+)在胶结物、裂隙中富集。     

Single copper sites dispersed on hierarchically porous carbon for improving oxygen reduction reaction towards zinc-air battery

The demand for high-performance non-precious-metal electrocatalysts to replace the noble metal-based catalysts for oxygen reduction reaction(ORR)is intensively increasing.Herein,single-atomic copper sites supported on N-doped three-dimensional hierarchically porous carbon catalyst(Cu₁/NC)was prepared by coordination pyrolysis strategy.Remarkably,the Cu₁/NC-900 catalyst not only exhibits excellent ORR performance with a half-wave potential of 0.894 V(vs.RHE)in alkaline media,outperforming those of commercial Pt/C(0.851 V)and Cu nanoparticles anchored on N-doped porous carbon(CuNPs/NC-900),but also demonstrates high stability and methanol tolerance.Moreover,the Cu₁/NC-900 based Zn-air battery exhibits higher power density,rechargeability and cyclic stability than the one based on Pt/C.Both experimental and theoretical investigations demonstrated that the excellent performance of the as-obtained Cu₁/NC-900 could be attributed to the synergistic effect between copper coordinated by three N atoms active sites and the neighbouring carbon defect,resulting in elevated Cu d-band centers of Cu atoms and facilitating intermediate desorption for ORR process.This study may lead towards the development of highly efficient non-noble metal catalysts for applications in electrochemical energy conversion.     

亲水性PET共混材料的制备及性能研究

以机械共混法制备亲水性聚对苯二甲酸乙二醇酯（PET）共混材料，并通过接触角测定仪、差示扫描量热仪(DSC)和电子万能材料试验机等对共混材料的亲水性能、热性能和力学性能等进行研究与分析。结果表明，亲水处理剂聚乙二醇（PEG）、聚丙烯酸钠（PAAS）、聚乙烯吡咯烷酮（PVP）均能改善PET的亲水性能，影响PET的结晶性能，但亲水处理剂对PET的力学性能影响较小，其中PET/PEG共混材料的亲水性最优；随着PEG含量的增加，PET/PEG共混材料的亲水性先逐渐增强，当PEG含量高于5 %后，共混材料的亲水性变化很小；且PET的结晶度随着PEG的加入呈现先增大后减小的趋势。